Paver work for Sewall’s Point homes and properties
Sewall’s Point is surrounded by water on three sides, so drainage and salt exposure drive most of the decisions.
What we see on Sewall’s Point properties
Sewall’s Point is surrounded by water on three sides, so drainage and salt exposure drive most of the decisions.
Almost every paver problem we get called out to is a base problem wearing a surface disguise. The pavers themselves are fine. They are concrete or stone, and they will outlast most of us. What moves is what is underneath them.
South Florida gives us two things that make base work matter more than it does up north: sand that moves when water runs through it, and rain that arrives all at once. A base that would be fine in a dry climate gets tested here every summer.
A lifted section near a tree is usually the roots. The base under pavers holds moisture, so roots grow into it and push the surface up as they get bigger.
We are out this way most weeks, so a look at the property is usually a matter of days rather than months. If it turns out the honest answer is that it can wait, we will tell you that too.
How a job here runs
We come look at it
Somebody from the crew comes out, stands on the problem, and tells you what is actually going on underneath it. No sales visit, just a look and an honest read.
You get the plan in writing
Scope, materials, how long it takes, and what it costs, written down before anybody starts. No verbal numbers that change later.
We build the base first
Dig to depth, compact the aggregate in layers, screed the bedding. Nobody ever sees this part again, which is exactly why most failures start here.
Pavers go down and get cut in
Field laid to the pattern, edges cut on site, and a restraint set around the perimeter so the field cannot creep.
Joints get filled and the site gets cleaned
Sand swept in and compacted, the surface washed down, and the property left the way we found it. We haul our own debris.
Why surfaces fail around here
Start at the bottom and work up. The subgrade is the soil your property already has, and nothing we do changes what it is made of. On top of it goes the base: crushed aggregate, compacted until it carries weight on its own. Then a thin course of sharp sand, screeded flat so every paver beds at the same height. Then the pavers. Three of those four layers get buried on the first day, and they are the three that decide how the job ages.
Put a walkway’s base under a driveway and the driveway tells you soon enough. Tire tracks show up as ruts, the edges spread and pavers start to rock. A walkway that only carries people can live on a shallower base. A daily pickup needs more depth, and delivery trucks on a commercial drive need more than that. We size the base to the heaviest thing that will cross it.
Settling that shows up a year after an install usually has the same cause. The base was compacted once, at full depth, so only the top few inches got tight. The rest stayed loose and slowly packed down under traffic and rain. We build bases in lifts, a few inches at a time, compacting each layer before the next goes on, so the whole depth is firm.
A sunken paver is a symptom. The base under it is the disease.
An eighth to a quarter inch per foot does not sound like much, and walking on it you would swear the surface is level. That small, steady drop away from the building is what carries water off. A flat surface holds puddles. A surface sloped the wrong way delivers runoff to the foundation, which is a far bigger problem.
Drainage is the cheapest thing to fix while the ground is open and the most expensive thing to add later. Once water leaves the paved surface it has to land somewhere, and on a tight commercial lot with no fall to work with, that takes planning. We look at a channel drain along the low edge, a permeable section over a stone reservoir, or regrading the planting bed next door.
Before we design anything, we find out where the water on the site comes from. The usual sources are a downspout discharging at the edge, an irrigation head spraying the same patch twice a day, and a neighboring grade sending runoff across a corner. Rain falling evenly on jointed pavers matters far less.
Separation
Geotextile between subgrade and base stops fine soil migrating up and destroying the aggregate structure.
Base depth
Set by what the surface carries, not by habit. A walkway and a truck-bearing drive are not the same excavation.
Compaction
Compacting the whole base in one go only firms up the top. We place aggregate in layers and compact each one, so the base is solid all the way down.
What Sewall’s Point calls us for
Also nearby in Martin County:
What we tend to use around here
Clay brick ages without changing color. The color is the fired clay, so sun has nothing to bleach out. It is more expensive and the shape options are narrower, and for a surface you want looking the same in twenty years, it is hard to beat.
Travertine is a natural stone, and it behaves like one. Color and texture shift from unit to unit, so a deck has a less uniform look than concrete pavers give you. It also stays cooler under bare feet in direct sun, which is why pool owners ask for it. Seal it if it is going to see oil or heavy stains.
Porcelain is the newest of these in residential work. It is dense, absorbs almost nothing, and is close to stain-proof. It needs precise base work because it is unforgiving of an uneven bed, and cutting it takes the right blade and patience.
The edge restraint is the piece nobody thinks about and it is what stops the whole field from spreading. Pavers work by interlock, which means each unit is held by its neighbors. Take away the restraint at the perimeter and the outermost course starts creeping outward, the joints open, the sand washes, and the failure marches inward from the edge.
You can see this on almost any failing driveway. The middle usually looks fine and the outer two feet are a mess with wide joints and rocking units. That is not the edge wearing out faster, it is the edge restraint having failed and the field unlocking from the outside in.
Finding us in Sewall’s Point
We are based in Miami and out this way regularly.
The failures we get called out to fix
These shortcuts all pass a walk-through on day one. The problems arrive later, and that delay is why they stay common.
Laying over the old surface
It is quick, it is cheap, and it inherits every problem underneath. If the base was the reason the old surface failed, putting a new one on top of it just hides the failure for a season.
Skipping the geotextile
When we tear out a failed paver job, a muddy base with no fabric under it is a common sight. The soil and the stone have blended into one weak layer. That is exactly what separation fabric is there to prevent, and why resetting pavers on top of that mess never holds.
Using the wrong sand in the bedding
Concrete sand goes in the bedding for a reason: its grains are sharp and angular, so they lock. Mason sand and beach sand are rounded and let pavers wander under load.
Sealing too early
Sealer works like a lid. Put it on a new concrete paver too early, in the first month, and whatever efflorescence has not come out yet gets trapped underneath as a permanent white haze. Let the pavers cure first.
Compaction in lifts is the difference between ten years and two.
Common questions
How long does the job take
A typical paver work job runs two to five working days once we start. Base work is the slow part; laying the field goes quickly. Weather moves things, and in summer we plan around the afternoon storms rather than pretending they will not happen.
Do I need to be home while you work
No. Access and a working hose bib are all we need. We will keep you posted as the job goes, and if we uncover something we did not expect, you get a call that day so you can decide with us.
Will the new pavers match what I already have
Often the best match is already on your property. When a new paver will not blend, we can pull units from a less visible area, use them on the visible patch, and put the new ones where nobody looks. Otherwise matches range from exact to close, because concrete pavers shift color a bit with sun and age.
What happens to the old surface
That part is on us. The existing surface gets broken out and hauled off the property, and concrete and pavers go to recycling when there is a recycler in the area. It is covered in the scope you sign.
How do you keep it from settling again
Pulling up the low pavers is the easy part. Keeping them level means fixing what let them drop, which is usually water undermining the base or a base that was weak to begin with. We correct both before anything goes back down, and handle a root if one is involved.
Do you cover Sewall’s Point, FL
Yes. Sewall’s Point, FL is inside our regular working area and we are out that way most weeks. Call and we will tell you honestly when we could get to you.
Let us walk the property
Send a couple of photos or just call. We will tell you what we think is going on, what it would take to fix, and whether it needs doing now or can wait.
Quality you can stand on